特性一覽

Mechanical Format 4-lane PCIe/104, stack-down only, universal peripheral module Cooling method Conduction cooling Mounting For stacking down directly under the Host PC: 1 or 2 modules on Type 1 and Type 2 Host PC's Connectors 'CAMERA POWER INPUT' 4-pin 0.1-in Molex KK 7478 male connector 'C2C-Link' 6-pin 2-row 0.1-in header 'I/O' on '3300 HD26F I/O module for Coaxlink Duo PCIe/104' (optional) 26-pin 3-row high-density female sub-D connector GPIO lines and power output 'A', 'B' on '3302 DIN1.0/2.3 Coaxial cable for Coaxlink Duo PCIe/104' (optional) DIN 1.0/2.3 female connectors CoaXPress host interface LED indicators 'A', 'B' on '3300 HD26F I/O module for Coaxlink Duo PCIe/104' (optional) 2x bi-color red/green LEDs CoaXPress Host connector indicator 'FPGA STATUS LAMP' on '3300 HD26F I/O module for Coaxlink Duo PCIe/104' (optional) Bi-color red/green LED 'BOARD STATUS LAMP' on '3300 HD26F I/O module for Coaxlink Duo PCIe/104' (optional) Bi-color red/green LED Switches 'RECOVERY' on card PCB: 3-pin 1-row 0.1" header Firmware emergency recovery Dimensions 96 mm x 90 mm 3.775 in x 3.555 in Weight 75 g, 2.65 oz without accessories Host bus Standard PCI Express 2.0 Link width 4 lanes 1 lane or 2 lanes with reduced performance Link speed 5.0 GT/s (PCIe 2.0) 2.5 GT/s (PCIe 1.0) with reduced performance Maximum payload size 512 bytes DMA 32- and 64-bit Peak delivery bandwidth 2,000 MB/s Effective (sustained) delivery bandwidth 1,700 MB/s (Host PC motherboard dependent) Power consumption Typ. 8.4 W @ +12V excluding I/O power output +3.3V and +5.0V rails are not used Camera / video inputs Interface standard(s) CoaXPress 1.0, 1.1 and 1.1.1 Connectors Two MCX 75 Ohms CXP-6 Status LEDs One CoaXPress Host connection status LED per connection Number of cameras Area-scan cameras: One 1- or 2-connection camera One or two 1-connection cameras Line-scan cameras: One 1- or 2-connection camera Maximum aggregated camera data transfer rate 12.5 Gbit/s (1,250 MB/s) Supported CXP down-connection speeds 1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), and 6.25 GT/s (CXP-6) Number of CXP data streams (per camera) 1 data stream per camera Maximum CXP stream packet size 16,384 bytes PoCXP (Power over CoaXPress) PoCXP Safe Power: 17 W of 24V DC power per CoaXPress connector PoCXP Device detection and automatic power-on Overload and short-circuit protections A +24V DC power source must be connected to the CAMERA POWER INPUT connector on the module Camera types Area-scan cameras: Grayscale and color (YCbCr, YUV, RGB and Bayer CFA) Single-tap (1X-1Y) progressive-scan Line-scan cameras and contact imaging sensors: Grayscale and color RGB Camera pixel formats supported Raw, Monochrome, Bayer, RGB, and RGBA (PFNC names): Raw Mono8, Mono10, Mono12, Mono14, Mono16 BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG RGB8, RGB10, RGB12, RGB14, RGB16 RGBA8, RGBA10, RGBA12, RGBA14, RGBA16 YCbCr601_422_8, YCbCr601_422_10 YCbCr709_422_8, YCbCr709_422_10 YUV422_8, YUV422_10 Area-scan camera control Trigger Precise control of asynchronous reset cameras, with exposure control. Support of camera exposure/readout overlap. Support of external hardware trigger, with optional delay and trigger decimation. Strobe Accurate control of the strobe position for strobed light sources. Support of early and late strobe pulses. Line-scan camera control Scan/page trigger Precise control of start-of-scan and end-of-scan triggers. Support of external hardware trigger, with optional delay. Support of infinite acquisition, without missing line, for web inspection applications. Line trigger Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation. Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%. Rate Divider tool Line strobe Accurate control of the strobe position for strobed light sources. On-board processing On-board memory 512 MB