可以連接多達4個定位/模擬量擴展單元。

5、利用內置能力FX2NC系列能控制兩軸（包括插補）或通過增加擴展單元能控制多軸

網路和數據通信功能

6、通過連接擴展板或特殊適配器能實現多種通信和數據鏈接。（四）、AB Micro Logix 1500 可編程序控制器

ROCKWELL-羅克韋爾自動化

Rockwell Automation(china)

Allen-Bradley

Micro Logix 1500 可編程序控制器，可按需要擴展I/O，與大型控制器相比，成本低，體積小。現代燃油燃燒機多為自動控制式的燃燒機，一般采用工業程序控制器、火焰檢測器以及溫度傳感器等組成自動控制系統。

本系統可以對燃燒機燃燒火焰狀況進行適時調節，既可單調風門、也可以單獨調整油門、還可以風油門聯動，進行風、油比例調整。具有手動/自動控制功能，并能與計算機進行實時通信。適用于各種工業鍋爐。適用燃料為：柴油、重油、渣油、及各種氣體燃料，并可單燒油、單燒氣、油氣混燒。燃油燃燒器工藝流程圖

系統啟動

↓

關閉風門、油門

↓

風機啟動

↓

打開風門

↓

吹掃爐膛

↓

關閉風門

↓

開啟油泵

↓

點火

↓ （點火不成功）

火焰檢測→報警→故障顯示→打開風門→ 后吹掃→　 停機

↓ （點火成功）

開啟油門調節閥至設定值

↓

開啟電磁閥

5秒后

開啟風門

↓

正常燃燒

↓

按設定溫度值自動控制燃燒過程

系統停止

↓

關閉電磁閥

↓

關閉油泵

↓

打開風門

↓

后吹掃

↓

停機

↓

燃油燃燒器的控制要求：real time through the modem and the public telephone network connected with Plc The system can prevent the failure of the system and take remedial measures in time. . Three . System Hardware Block diagram input part: The input part includes analog signal input and switch signal input two parts. The analog signals include an suction pressure sensor (0 ~ 200 PSIG) mounted on the suction manifold, an exhaust pressure Sensor (0 ~ 500 PSIG) mounted on the exhaust manifold, and a temperature sensor. And a voltage sensor to monitor the system's supply voltage . Switch signals include: electronic thermal protection mounted on the compressor (temperature probe mounted in the motor windings) , low-pressure switch installed on the suction side of the compressor, high-pressure switch installed on the exhaust side of the compressor, oil level controller, oil pressure differential controller, send a switch signal, when the temperature is higher than the set value of the control circuit, otherwise turn on the control circuit, mainly to prevent the compressor winding temperature caused by the fault . The low-pressure switch installed in the suction side of the compressor is mainly used to control the opening/closing of the compressor according to the suction pressure when the system enters the mechanical standby state . The high-pressure switch installed on the exhaust side of the compressor is used to disconnect the control loop when the exhaust pressure exceeds the