I（BS）標準是由英國標準協會（BritishStandards Institution，簡稱BSI）制訂的英國標準。BSI是在國際上具有較高聲譽的非機構，1901年成立，是早的全國性標準化機構，它不受政府控制但得到了政府的大力支持。BSI制定和修訂英國標準，并促進其貫徹執行。
英國中壓電網電壓為：11kv 33kv。低壓電壓為：240V/50Hz 。恒豐友電氣符合BS、KEMA標準，已為多家英國變壓器公司提供油浸式變壓器鐵芯及變壓器定制服務。
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| BS 148-1998 | 變壓器和開關設備未用過的和回收的礦物絕緣油規范 | Specification for unused and reclaimed mineral insulating oils for transformers and switchgear |
| BS 2538-1954 | 高壓供電系統用氣冷式防火單相照明變壓器裝置規范 | Specification for air-cooled flameproof single-phase lighting transformer units supplied from high voltage systems |
| BS 2562-1979 | 變壓器與電抗器用電纜箱規范 | Specification for cable boxes for transformers and reactors |
| BS 2857-1976 | 鎳鐵制變壓器與扼流圈疊片規范 | Specification for nickel-iron transformer and choke laminations |
| BS 2G 127-1967 | 航空供電系統用電力變壓器和電流互感器規范 | Specification for power and current transformers for use in aircraft electrical power supply systems |
| BS 3399-1961 | 船舶用變壓器規范 | Specification for transformers for use in ships |
| BS 4727-2 Group 04-1991 | 電工、電力、電信、電子學、照明和顏色術語.第2部分:電力工程專用術語.第04集:變壓器和電抗器 | Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms - Terms particular to power engineering - Power transformers and reactors |
| BS 4727-2 Group 16-1991 | 電工、電力、電信、電子、照明和顏色術語.第2部分:電力工程術語.第16集:儀表用變壓器 | Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms - Terms particular to power engineering - Instrument transformers |
| BS 4819-1-1989 | 壓裝和便攜式電阻焊水冷變壓器.第1部分:壓裝式變壓器規范 | Resistance welding water-cooled transformers of the press package and portable types - Specification for press-package transformers |
| BS 4819-2-1989 | 壓裝和便攜式電阻焊水冷變壓器.第2部分:便攜式變壓器規范 | Resistance welding water-cooled transformers of the press-package and portable types - Specification for portable transformers |
| BS 5067-1985 | 礦山用防火變壓器規范 | Specification for flameproof transformers for use in mines |
| BS 5126-3-1993 | 電壓可達1100V的系統用礦山型阻燃式電源和控制裝置.第3部分:氣冷式照明用變壓器裝置規范 | Mining type flameproof supply and control units for use on systems up to 1100 V. Specification for air-cooled lighting transformer units |
| BS 5126-4-1993 | 電壓可達1100V的系統用礦山型阻燃式電源和控制裝置.第4部分:鉆機供電裝置的氣冷變壓器規范 | Mining type flameproof supply and control units for use on systems up to 1100 V. Specification for air-cooled transformers to power drilling machines |
| BS 5336-1976 | 高磁通密度變壓器用鐵氧體鐵芯規范 | Specification - Cores made of ferromagnetic oxides for use in high flux density transformers |
| BS 5347-1976 | 電信和電子設備變壓器和感應線圈用的硅鐵帶繞鐵芯規范 | Specification for silicon-iron strip-wound cores for use in transformers and inductors for telecommunications and electronic equipment |
| BS 5938-1-1984 | 電信用感應器及變壓器鐵芯.第1部分:測量方法 | Cores for inductors and transformers for telecommunications - Methods of measurement |
| BS 5938-2-1980 | 電信用感應器及變壓器鐵芯.第2部分:性能規范編制導則 | Cores for inductors and transformers for telecommunications - Guide to the drafting of performance specifications |
| BS 6184-1981 | 儀表變壓器部分放電測量方法 | Method for measuring partial discharges in instrument transformers |
| BS 6435-1984 | 變壓器與電抗線圈的高壓電纜干燥端子用未充填護套規范 | Specification for unfilled enclosures for the dry termination of HV cables for transformers and reactors |
| BS 6436-1984 | 電纜箱或分電站連接用接地配電變壓器規范 | Specification for ground mounted distribution transformers for cable box or unit substation connection |
| BS 6553-1984 | 變壓器電路設備用高壓熔斷絲的熔絲連接器選擇指南 | Guide for selection of fuse links of high-voltage fuses for transformer circuit applications |
| BS 6556-2-1985 | 煤礦用低速數字信號.第2部分:變壓器耦合規范 | Low speed digital signals for use in coal mines - Specification for transformer coupling |
| BS 6600-1-1987 | 通信與電子設備用變壓器與電感器的外形尺寸.第1部分:使用YEI-1疊片的變壓器和電感器的外形尺寸規格 | Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Specification for the outline dimensions of transformers and inductors using YEI-1 laminations |
| BS 6600-10-1985 | 通信與電子設備用變壓器與電感器的外形尺寸.第10部分:使用C-磁芯Q范圍的變壓器與電感器的外形尺寸規范 | Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Specification for the outline dimensions of transformers and inductors using the Q range of C-cores |
| BS 7452-1991 | 、自耦變壓器、可變變壓器和電抗器規范 | Specification for separating transformers, autotransformers, variable transformers and reactors |
| BS 7713-1993 | 變壓器硅油維護指南 | Guide for the maintenance of silicone transformer liquids |
| BS 7729-1994 | 儀表變壓器規范.電壓標準為U不超過52KV的三相變壓器 | Specification for instrument transformers - Three-phase voltage transformers for voltage levels having Um up to 52 kV |
| BS 7735-1994 | 油浸電力變壓器負荷指南 | Guide to loading of oil-immersed power transformers |
| BS 7821-1-1995 | 小于36KV設備的電壓值為50Hz、50-2500KVA三相油浸式配電變壓器.小于24KV設備的電壓值變壓器的一般 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - General requirements and requirements for transformers with highest voltage for equipment not exceeding 24 kV |
| BS 7821-2.1-1995 | 電壓不超過36KV的設備用的50Hz、50-2500KVA三相油浸式配電變壓器.帶有高壓和/或低壓端電纜接線盒的配電 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Distribution transformers with cable boxes on the high voltage and/or low voltage side - General requirements |
| BS 7821-2.2-1998 | 50HZ,電壓不超過36KW的由50-2500KVA的三相油浸配電變壓器.帶高壓和/或低壓單側電纜盒的配電變壓器.與BS | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Distribution transformers with cable boxes on the high voltage and/or low voltage side - Cable boxes of type 1 for use on distribution transformers meeting the requirements of BS 7821-2.1 |
| BS 7821-2.3-1998 | 小于36KV設備的電壓值為50Hz、50-2500KVA三相油浸式配電變壓器.位于高壓線和/或低壓線邊的電纜盒配電變 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Distribution transformers with cable boxes on the high voltage and/or low voltage side - Cable boxes type 2 for use on distribution transformers meeting the requirements of BS 7821-2.1 |
| BS 7821-3-1995 | 小于36KV設備的電壓值為50Hz、50-2500KVA三相油浸式配電變壓器.36KV設備的電壓值變壓器補充要求 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Supplementary requirements for transformers with highest voltage for equipment equal to 36 kV |
| BS 7821-4-1995 | 小于36KV設備的帶有電壓值50Hz、50-2500KVA三相油浸式配電變壓器.載有非正弦電流的變壓器額定功率測定 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Determination of the power rating of a transformer loaded with non-sinusoidal currents |
| BS 7821-6-2002 | 電壓不超過36KV的設備用50Hz、50～2500KVA三相油浸式配電變壓器.關于加壓波紋罐的要求和試驗方法 | Three phase oil-immersed distribution transformers, 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Requirements and tests concerning pressurized corrugated tanks |
| BS 7844-1-1996 | 小于36KV設備的電壓值為50Hz、100-2500KVA三相干式配電變壓器.第1部分:小于24KV設備的電壓變壓器的 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - General requirements and requirements for transformers with highest voltage for equipment not exceeding 24 kV |
| BS 7844-2-1996 | 小于36KV設備的電壓值為50Hz、100-2500KVA三相干式配電變壓器.第2部分:設備電壓為36KV變壓器的補充 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Supplementary requirements for transformers with highest voltage for equipment equal to 36 kV |
| BS 7844-3-1998 | 小于36KV設備的電壓值為50Hz、100-2500KVA三相干式配電變壓器.負載非正弦電流的變壓器額定功率的測定 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Determination of the power rating of a transformer loaded with non-sinusoidal current |
| BS 787-3-1971 | 礦用式防爆電纜終端箱規范.第3部分:帶照明變壓器的電纜終端箱 | Specification for mining type flameproof gate-end boxes - Gate-end boxes with lighting transformers |
| BS 9720-1989 | 經質量評定的定制變壓器和電感器規范:通用數據和試驗方法 | Specification for custom-built transformers and inductors of assessed quality: generic data and methods of test |
| BS 9721-1985 | 經質量評定的信號變壓器的電子設備性能鑒定分規范 | Sectional specification for signal transformers of assessed quality for use in electronic equipment for capability approval |
| BS 9727-1985 | 電子設備性能鑒定用的經質量評定的電源變壓器分規范 | Sectional specification for power transformers of assessed quality for use in electronic equipment for capability approval |
| BS 9733-1985 | 電子設備性能鑒定用的經質量評定的脈沖變壓器分規范 | Sectional specification for pulse transformers of assessed quality for use in electronic equipment for capability approval |
| BS 9925 Pt.02.01 and Pt.02.02-1988 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁心.第2部分:空白詳細規范:寬帶變壓器用磁氧化物磁心. | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Blank detail specification: magnetic oxide cores for broad-bａnd transformers - Assessment levels A and B |
| BS 9925-0-1984 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁芯.第0部分:一般規范 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Generic specification |
| BS 9925-01.0-1984 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁芯.第1部分:分規范:電感器用磁性氧化物磁心 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Sectional specification: magnetic oxide cores for inductor applications |
| BS 9925-01.01-1984 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁芯.第1部分:空白詳細規范:電感器用磁性氧化物磁心.第 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Blank detail specification: magnetic oxide cores for inductor applications - Assessment level A |
| BS 9925-02.0-1987 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁心.第2部分:分規范:寬帶變壓器用磁氧化物磁心 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Sectional specification: magnetic oxide cores for broad-bａnd transformers |
| BS 9925-03.0-1988 | 電子元器件用經質量評估的協調體系.通信用電感器和變壓器磁心.第3部分:分規范:功率用變壓器和扼流圈的磁氧 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Sectional specification: Magnetic oxide cores for transformers and chokes for power applications |
| BS 9925-03.01-1988 | 電子元器件用質量評估協調體系.通信用電感器和變壓器磁心.第3部分:空白詳細規范:功率用變壓器和扼流圈磁氧 | Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Blank detail specification: magnetic oxide cores for transformers and chokes for power applications - Assessment level A |
| BS DD ENV 50232-1997 | 航空用地面照明電氣設施..設備規范和試驗 | Aeronautical ground lighting electrical installation - Isolating transformer - Equipment specifications and tests |
| BS EN 125200-1978 | 電子元器件質量評定統一體系.分規范.線性變壓器用磁性氧化鐵芯 | Harmonized system of quality assessment for electronic components: sectional specification: magnetic oxide cores for linear transformers |
| BS EN 125400-1984 | 電子元件質量評定協調體系.分規范.電感器和調諧變壓器與磁性氧化鐵芯一起使用的調節器 | Harmonized system of quality assessment for electronic components: sectional specification: adjusters used with magnetic oxide cores for use in inductors and tuned transformers |
| BS EN 125401-1984 | 電子元器件的質量保證協調體系.空白詳細規范.電感器和調諧變壓器用具有磁性鐵氧體鐵芯的調整器 | Harmonized system of quality assessment for electronic components - Blank detail specification - Adjusters used with magnetic oxide (ferrite) cores for use in inductors and tuned transformers |
| BS EN 2591-704-2001 | 電氣和光學連接元件.試驗方法.電氣元件.耦合器用的變壓器的線圈系數的測量 | Elements of electrical and optical connection - Test methods - Electrical elements - Measurement of turns ratio on a transformer used in a coupler |
| BS EN 50152-3-2-2001 | 鐵路設施.固定裝置.交流電開關的專門要求.交流牽引系統特殊使用的測量、控制和保護裝置.單相電流變壓器 | Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Measurement, control and protection devices for specific use in a.c. traction systems - Single-phase current transformers - Single-phase current transformers |
| BS EN 50152-3-3-2001 | 鐵路設施.固定裝置.交流電開關的專門要求.交流牽引系統特殊使用的測量、控制和保護裝置.單相感應電壓變壓器 | Railway applications - Fixed installations - Particular requirements for a.c. switchgear - Measurement, control and protection devices for specific use in a.c. traction systems - Single-phase inductive voltage transformers - Single-phase voltage transformers |
| BS EN 50180-1999 | 充液變壓器用大于1kV但可達36kV和范圍為250A至3.15kA的套管 | Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers |
| BS EN 50181-1999 | 不包括液體填充變壓器在內的設備用大于1KV和達36KV范圍為250A到1.25KA的插入型套管 | Plug-in type bushings above 1 kV up to 36 kV and from 250 A to 1.25 kA for equipment other than liquid filled transformers |
| BS EN 50216-1-2002 | 電力變壓器和反應堆配件.總則 | Power transformers and reactor fittings - General |
| BS EN 50216-2-2002 | 電力變壓器和反應堆配件.液浸變壓器和有存油器的反應堆用氣體和油驅動的繼電器 | Power transformers and reactor fittings - Gas and oil actuated relay for liquid immersed transformers and reactors with conservator |
| BS EN 50216-3-2002 | 電力變壓器和反應堆配件.密封的液浸變壓器和無氣墊反應堆用保護繼電器 | Power transformers and reactor fittings - Protective relay for hermetically sealed liquid-immersed transformers and reactors without gaseous cushion |
| BS EN 50216-4-2002 | 電力變壓器和反應堆配件.基本附件(接地端子、排水和填充裝置、溫度計套和輪組件) | Power transformers and reactor fittings - Basic accessories (earthing terminal, drain and filling devices, thermometer pocket, wheel assembly) |
| BS EN 50216-5-2002 | 電力變壓器和反應堆配件.液位、壓力裝置和流量指示計 | Power transformer and reactor fittings - Liquid level, pressure and flow indicators, pressure relief devices and dehydrating breathers |
| BS EN 50216-6-2002 | 電力變壓器和反應堆配件.冷卻設備.油浸變壓器的活動散熱器 | Power transformers and reactor fittings - Cooling equipment - Removable radiators for oil-immersed transformers |
| BS EN 50216-7-2002 | 電力變壓器和反應堆配件.運輸油用電泵 | Power transformers and reactor fittings - Electric pumps for transformer oil |
| BS EN 50243-2002 | 充液變壓器用 24 kV、36 kV、5 kA 和 8 kA 的戶外套管 | Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers |
| BS EN 50299-2002 | UDOWNm設備的電壓從72.5 kV - 550 kV的變壓器和電抗器用浸油式電纜連接組件 | Oil-immersed cable connection assemblies for transformers and reactors having highest voltage for equipment Um from 72,5 kV to 550 kV |
| BS EN 50329-2003 | 鐵路設施.固定式裝置.牽引變壓器 | Railway applications - Fixed installations - Traction transformers |
| BS EN 50336-2002 | 不超過36kV的變壓器和電抗器電纜盒用套管 | Bushings for transformers and reactor cable boxes not exceeding 36 kV |
| BS EN 50386-2003 | 充液變壓器用1KV以下和250A至5KA的套管 | Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers |
| BS EN 50387-2003 | 充液變壓器用1KV以下和125A至5KA的母線套管 | Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformers |
| BS EN 60044-1-1999 | 儀表變壓器.電流互感器 | Instrument transformers - Current transformers |
| BS EN 60044-2-1999 | 儀表變壓器.感應變壓器 | Instrument transformers - Inductive voltage transformers |
| BS EN 60044-3-2003 | 儀表用變壓器.組合變壓器 | Instrument transformers - Combined transformers |
| BS EN 60044-6-1999 | 儀表變壓器.保護電流變壓器瞬時特性要求 | Instrument transformers - Requirements for protective current transformers for transient performance |
| BS EN 60044-7-2000 | 儀表用變壓器.電壓變換器 | Instrument transformers - Electronic voltage transformers |
| BS EN 60044-8-2002 | 儀表變壓器.電流變壓器 | Instrument transformers - Electronic current transformers |
| BS EN 60076-1-1997 | 電力變壓器.第1部分:通則 | Power transformers - General |
| BS EN 60076-10-2001 | 電力變壓器.聲音水平測定 | Power transformers - Determination of sound levels |
| BS EN 60076-11-2004 | 電力變壓器. | Power transformers — Part 11: Dry-type transformers |
| BS EN 60076-2-1997 | 電力變壓器.升溫 | Power transformers - Temperature rise |
| BS EN 60076-3-2001 | 電力變壓器.絕緣水平和介質性能試驗以及露天外部間隙 | Power transformers - Insulation levels, dielectric tests and external clearances in air |
| BS EN 60076-4-2002 | 電力變壓器.電光脈沖和轉換脈沖測試指南.電力變壓器和電抗器 | Power transformers - Guide to the lightning impulse and switching impulse testing - Power transformers and reactors |
| BS EN 60076-5-2001 | 電力變壓器.耐短路性 | Power transformers - Ability to withstａnd short circuit |
| BS EN 60310-2004 | 鐵路設施.鐵道車輛上的牽引變壓器和電感器 | Railway applications - Traction transformers and inductors on board rolling stock |
| BS EN 60401-3-2004 | 磁性軟鐵氧體制磁芯的術語和命名.寫入變壓器和電感器磁芯制造廠產品目錄中的數據格式指南 | Terms and nomenclature for cores made of magnetically soft ferrites - Guidelines on the format of data appearing in manufacturers' catalogues of transformer and inductor cores |
| BS EN 60740-1-2005 | 變壓器和電感器用疊層鐵芯.機械和電氣特性 | Laminations for transformers and inductors - Mechanical and electrical characteristics |
| BS EN 60852-4-1997 | 電信和電子設備用變壓器和電感器外形尺寸.第4部分:使用YEI-2型疊片的變壓器和電感器 | Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Transformers and inductors using YUI-2 laminations |
| BS EN 61007-1997 | 電信和電子設備用變壓器和電感器.測量方法和試驗規程 | Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures |
| BS EN 61021-1-1990 | 電信和電氣設備用變壓器和電感器疊片鐵心包.第1部分:尺寸規范 | Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment - Specification for dimensions |
| BS EN 61021-2-1997 | 電信和電氣設備用變壓器和電感器疊片鐵心包.第2部分:YEE 2疊片鐵芯電器性能 | Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment - Electrical characteristics for cores using YEE 2 laminations |
| BS EN 61050-1992 | 空載輸出電壓超過1000V的管形放電燈用變壓器規范(一般稱為氖管變壓器).一般要求和安全要求 | Specification for transformers for tubular discharge lamps having a no-load output voltage exceeding 1000 V (generally called neon-transformers) - General and safety requirements |
| BS EN 61203-1995 | 電工用合成有機酯.設備中變壓器酯的維護指南 | Synthetic organic esters for electrical purposes - Guide for maintenance of transformer esters in equipment |
| BS EN 61248-1-1997 | 電子和電信設備用變壓器和電感器.第1部分:通用規范 | Transformers and inductors for use in electronic and telecommunication equipment - Generic specification |
| BS EN 61248-2-1997 | 電子和電信設備用變壓器和電感器.第2部分:信號變壓器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for signal transformers on the basis of the capability approval procedure |
| BS EN 61248-3-1997 | 電子和電信設備用變壓器和電感器.第3部分:電力變壓器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for power transformers on the basis of the capability approval procedure |
| BS EN 61248-4-1997 | 電子和電信設備用變壓器和電感器.第4部分:轉換供電方式的電力變壓器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for power transformers for switched mode power supplies (SMPS) on the basis of the capability approval procedure |
| BS EN 61248-5-1997 | 電子和電信設備用變壓器和電感器.第5部分:脈沖變壓器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for pulse transformers on the basis of the capability approval procedure |
| BS EN 61248-6-1997 | 電子和電信設備用變壓器和電感器.第6部分:電感器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for inductors on the basis of the capability approval procedure |
| BS EN 61248-7-1998 | 電子和電信設備用變壓器和電感器.第7部分:高頻電感器和中頻變壓器性能批準程序分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Sectional specification for high-frequency inductors and intermediate transformers on the basis of the capability approval procedure |
| BS EN 61262-7-1996 | 醫用電氣設備.電光X射線圖象增強器特性.第7部分:調制變壓器函數測定 | Characteristics of electro-optical X-ray image intensifiers for medical electrical equipment - Determination of the modulation transfer function |
| BS EN 61378-1-1999 | 變流變壓器.工業用變壓器 | Convertor transformers - Transformers for industrial applications |
| BS EN 61378-2-2001 | 轉換變壓器.HVDC用變壓器 | Convertor transformers - Transformers for HVDC applications |
| BS EN 61558-1-2005 | 電力變壓器、供電、反應堆及類似設備的安全.一般要求和試驗 | Safety of power transformers, power supplies, reactors and similar products — Part 1: General requirements and tests |
| BS EN 61558-2-1-1998 | 電源變壓器、供電設備及類似設備安全性.通用分立變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for separating transformers for general use |
| BS EN 61558-2-12-2001 | 電力變壓器、供電設備及類似設備的安全性.恒壓變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for constant voltage transformers - Particular requirements for constant voltage transformers |
| BS EN 61558-2-13-2000 | 電力變壓器、供電設備及類似設備的安全性.通用自耦變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for auto-transformers for general use - Particular rquirements - auto-transformers |
| BS EN 61558-2-15-2001 | 電力源變壓器、供電設備及類似設備的安全性.醫用分立供電變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for isolating transformers for the supply of medical locations |
| BS EN 61558-2-17-1998 | 電源變壓器、供電設備及類似設備安全性.開關式供電系統變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for transformers for switch mode power supplies |
| BS EN 61558-2-19-2001 | 電源變壓器、供電設備及類似設備的安全性.擾動衰減變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for perturbation attenuation transformers - Part 2-19: Particular requirement Mains-born perturbatiion attenuation transformers |
| BS EN 61558-2-2-1998 | 電力變壓器、供電設備及類似設備的安全.控制變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for control transformers |
| BS EN 61558-2-20-2001 | 電源變壓器、供電設備及類似設備的安全性.小型電抗器特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for small reactors - Part 2-20: Particular requirements for small reactors |
| BS EN 61558-2-23-2001 | 電源變壓器、供電設備及類似設備安全性.建筑工地變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for transformers for construction sites |
| BS EN 61558-2-3-2000 | 電力變壓器、供電設備及類似設備的安全性.燃氣及燃油燃燒器用點火變壓器的特殊要求.燃氣及燃油燃燒器用點火 | Safety of power transformers, power supply units and similar - Particular requirements for ignition transformers for gas and oil burners - Ignition transformers for gas and oil burners |
| BS EN 61558-2-4-1998 | 電源變壓器、供電設備及類似設備安全性.通用隔離變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for isolating transformers for general use |
| BS EN 61558-2-5-1998 | 電力變壓器、供電設備及類似設備的安全.剃須刀變壓器和剃須刀供電裝置的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for shaver transformers and shaver supply units |
| BS EN 61558-2-6-1998 | 電源變壓器、供電設備及類似設備安全性.通用安全隔離變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for safety isolating transformers for general use |
| BS EN 61558-2-7-1998 | 電力變壓器、供電設備及類似設備的安全.玩具用變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Particular requirements for transformers for toys |
| BS EN 61558-2-8-1999 | 電源變壓器、供電設備及類似設備安全性.鈴聲和鐘聲變壓器專門要求 | Safety of power transformers, power supply units and similar - Particular requirements for bell and chime transformers |
| BS EN 61558-2-9-2003 | 電力變壓器、供電設備及類似設備的安全.Ⅲ類手抽式鎢絲燈的變壓器的特殊要求 | Safety of power transformers, power supply units and similar products - Particular requirements for transformers for class III handlamps for tungsten filament lamps |
| BS EN 61596-1997 | 電感器和變壓器用磁氧化EP芯和相伴部件.尺寸 | Magnetic oxide EP-cores and associated parts for use in inductors and transformers - Dimensions |
| BS EN 61797-1-1997 | 電信和電子設備變壓器和感應器.線圈架主要尺寸.疊層鐵芯線圈架 | Transformers and inductors for use in telecommunication and electronic equipment - Main dimensions of coil formers - Coil formers for laminated cores |
| BS EN 61823-2003 | 機場照明和信標導航用電氣設備.AGL系列變壓器 | Electrical installations for lighting and beaconing of aerodromes - AGL series transformers |
| BS EN 62041-2003 | 電力變壓器、電源裝置、電抗器和類似產品.電磁兼容性要求 | Power transformers, power supply units, reactors and similar products - EMC requirements |
| BS EN 5826-2003 | 電阻焊設備.變壓器.適用于各種變壓器的一般規范 | Resistance welding equipment - Transformers - General specifications applicable to all transformers |
| BS EN 7284-1996 | 電阻焊設備.汽車工業用多點點焊的兩個單獨副線圈的變壓器詳細規范 | Resistance welding equipment - Particular specifications applicable to transformers with two separate secondary windings for multi-spot welding as used in the auto industry |
| BS G 209-1970 | 變壓器整流裝置規范 | Specification for transformer rectifier units |
| BS 60076-8-1998 | 電力變壓器.應用指南 | Power transformers - Application guide |
| BS 60092-303-2002 | 船上電氣設施.設備.動力和照明用變壓器 | Electrical installation in ships - Equipment - Transformers for power and lighting |
| DD ENV 50232-1997 | 航空地面照明電子設備.絕緣變壓器的設備規范和試驗 | Aeronautical ground lighting electrical installation. Isolating transformer. Equipment specifications and tests |
| 編號 | 中文名稱 | 英文名稱 |
